Digisat Pro Accu MKII Emitor Meter

New Digisat Pro Accu MKII Emitor Meter

    Metal case which makes the unit more sturdy
    Easy to open battery compartment making it simple to replace the battery-pack
    Replaceable F-connectors (standard F- female/female) as the old type got worn out after some time
    New carrying-case

DIGISAT PRO ACCU MKII is microprocessor controlled, making it very reliable and accurate.
The instrument is unique as it can measure satellite signal from two LNBs at the same time. Signalstrength is presented graphical on the LCD-display in form of thermometer-scales and in numbers (from 0-99.9).
DIGISAT PRO ACCU MKII is very sensitive and can detect the weakest of signals. Strong incoming signals (powerfull satellites, big dishes) can easily be attenuated for better readout.

DIGISAT PRO ACCU MKII can identify the different signals coming from a receiver like; voltage+mA, 22 kHz and DiSEqC. It can also be setup as a 2-way switch (22 kHz, DiSEqC, Toneburst and 13/18v) making it very useful when testing systems.

The instrument can control and run any DiSEqC 1.2 actuator (also NOKIA SatScan and TRIAX H/H).The combination of actuator control and satfinder is something really needed on the market today.

DIGISAT PRO ACCU MKII is power supplied either by the integrated rechargeable battery or from a receiver (through coax). The unit is operational for about an hour with a fully charged battery. Charging of the unit is done with the enclosed power supply or car-charger. It takes about 14 hours to recharge a fully drained battery.

The inputs are short-circuit protected by automatic fuses.

Even though the DIGISAT PRO ACCU MKII has a lot of functions it is still very easy to use and has a very compact design.

The unit is delivered with a carrying case, power supply, car charger and manual.

    Measure on 2 LNB's at the same time.
    Can detect 13/18 V (and mA) +22 kHz + DiSEqC from the receiver.
    Can transmit 22 kHz and DiSEqC to the LNB.
    Can be set up as a 2-way switch (13/18 V, 22 kHz and DiSEqC).
    Can run a DiSEqC - actuator (East/West) with DiSEqC 1.2.
    Built in beeper and rechargeable battery pack

Features:

Measure signal level from two LNB´s at the same time.
Measured information are displayed on the LCD.
DiSEqC, 22 kHz, 13/18v and mA readout.
Generate DiSEqC, 22 kHz and 13/18v to control LNB/switch.
Also works as a 2-way switch (13/18v, 22 kHz or DiSEqC).
Operates DiSEqC 1.2 actuators (East/West and reset).
Built in beeper, higher tone - better signal.
Very sensitive, easy to maximize weak and strong signals.
950-2150 MHz input frequency.
F-connectors, CE-approved.

Technical specification
    
Input frequency: 2 x 950-2150 MHz.
Input level: 40-100 dBuV.
Through loss: 5 dB.
Input impedance: 75 Ohm, F-connectors.
Output impedance: 75 Ohm, F-connector.
Short circuit protection: Automatic fuses on all inputs.
Measuring method: Signal presentation on LCD display
in form of thermometer scales
or three digit number. Pitch-tone
indication on loudspeaker.
Max-level: Thermometer-scales showing
max. Three digit numbers showing
highest value. Highest tone on
loudspeaker. Maxhold-function.
Voltmeter: Voltmeter 0-30 volt. 0-900 mA.
Indications: Voltage, current. 22 kHz (on/off).
MiniDiSEqC (toneburst). DiSEqC
1.0 and 1.1
Transmitting: 22 kHz (on/off). MiniDiSEqC (toneburst).
DiSEqC 1.0 and 1.1 13/18V.
Actuator control: DiSEqC 1.2.
Power supply: Rechargeable battery or from
receiver via coaxial cable.
Power consumption: Ca 35 mA without loudspeaker.
Ca 50 mA with loudspeaker.
Battery recharge: Power supply 14-20V DC,
Centerpin +, Car-charger.
Weight: 400g.
Dimensions: 175x 55 x 40 mm.

Accessories:

Power supply.
Carrying-case.
Car-charger.
Manual